I got up early today with the view of getting outside and working a bit while it was cooler. That is, if you call 80 degrees cool as it quickly warms up here in my part of Texas. The overnight low was 74 and the forecast was for it to be at least a 100 degrees and could go as high as 104.
I had a couple of small projects that I wanted to get done. After the success of changing out the filter material in the big ponds and the small ponds filter systems to Lava Rock, I really wanted to do the same thing for the rest of the filters that I have located on the various ponds.
So, this morning I started out by building a new Skippy filter using a 20 gallon tub. I needed to do some work to it first like drill a hole and install the 2 inch drain system. I found a 2 inch fitting that reduced to 1 1/2 inch threaded fitting that had a flat area wide enough to take a rubber washer. I cut the washers (2) out of an old piece of liner material and placed both of them over the threaded end. I followed up with a thin layer of Plumbers Putty and then placed it through the hole with the threaded area inside the tub. On the threaded area, I didn’t have a washer large enough to fit over the 1 1/2 inch screw fitting so I had to make do with a piece of hard plastic from a storage box that I had also cut out a 1 1/2 inch hole. I secured the whole thing with a threaded ring washer used on electrical conduit. It worked perfectly and after tightening the whole thing up I finished it by placing 2 inch Tee fitting set parallel to the pond level so that water could flow out both sides.
In the bottom, I needed to make a water chamber so that the water would have a free flow as it came out before rising up through the lava rock to the drain. For this, I use 2 layers of plastic fluorescent light grid cut to shape and set up on 2 bricks, one either side of the pipe. The pipe itself is 2 inch and is set like an inverted Tee. On the ends of the Tee were 90 degree opposing elbows to create a flow of water. The center upright stands just above the rim of the tube and is eventually connected to the pipe from the pump. The theory is that the water comes in the top and then circulates from the bottom so that it comes through the Lava Rock and out the drain and back into the pond. The Lava Rock traps the dirt pretty efficiently. The 100 gallon one that I have installed on the big pond has really cleaned up that water. Incidentally, it works well to not glue the elbow situated on the top of the inverted Tee. This allows for easy removal of the grid when it is time to clean the unit. Otherwise, the center hole has to be pretty big to slide the grid over the elbow.
After completing the construction, with the final hook ups done in place, I filled it with 2 bags of the Lava Rock and then turned on the water to check that it worked properly. Satisfied with my work, I turned my attention to the old existing Skippy filter. I wanted to move it to a different location so that I could feed it with the main pump which is why I opted to build a new unit giving me more time to move the existing filter which is powered by a separate pump and contains the old filter material which I am replacing with the Lava Rock.
Moving it from its current location turned out to be easier than I had anticipated. Using mostly brute force and the judicious placing of a short 2 x 6, I moved it out onto the path and maneuvered it onto my dolly to be wheeled to the pond nursery area where I start all of the new pond plants. I will remove the Iris currently growing in it, clean it out and make any repairs that are needed and re-use it on one of the other ponds. With it gone, I was able to spend time on tightening up the electric fencing around that pond. I have fencing powered by a doggie shocker around all of my ponds to keep the Herons and Raccoons away from the very large Koi. You can see the fences in the pictures although they barely register with me as I am so used to them.
Now that I have a “spare” 20 gallon filter unit, I can take my time in preparing it to replace one or the other of the 2 existing ones that I have left, both of which have pretty extensive growths of Iris and Orange Canna. I may wait until the winter when the growth had died down before working on these two. As I pointed out above, the current “spare” unit also has a large growth of Iris in it which I need to dig out and re-plant somewhere or I might just give the Iris away. By the way, I do NOT plan on planting anything in the new filters. I would prefer they do not get enmeshed with roots even though the roots also act as a filter.
It took me all day to complete the project, I had to take a break and go to Home Depot for the fluorescent light grid as I was out of it but this only took about 30 minutes. Needless to say, my car would not drive past the Starbucks in Bee Cave so I had to humor it and buy a small latte. This tied me over until around 4:00 pm when I stopped for a tea break, but other than that, I was at it all the time. Funnily enough, even though it was a 100+ degrees, I never felt at any time that it was too hot to finish the project. I made sure I had plenty of water and I had liberally applied sun block and I was working in the shade for most of the time.
Must be getting used to the heat…..again.
If you click on any of the pictures, they will enlarge and can be quickly changed by use of the side arrows. To get back to the blog, press the escape key.